Welcome to the Australian Ford Forums forum.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact us.

Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated.

Go Back   Australian Ford Forums > Club and Speciality Forums > Forum Community Car Clubs > OzECruisers (E/N/D Series) > OzECruisers General Discussions

OzECruisers General Discussions E/N/D vehicles General Discussion ONLY. NO TECH THREADS

Reply
 
Thread Tools Display Modes
Old 23-08-2014, 05:52 PM   #1
car10002
FF.Com.Au Hardcore
 
Join Date: Aug 2010
Posts: 1,646
Default heavy duty tow bar

hi bought a heavy duty tow bar and wondered about the triangle bit in the boot how youd get around the gas tank.


the attached photo which is off the internet will give some idea,

http://i1049.photobucket.com/albums/...ps0d871663.jpg

where the long flat bar is in front of that or somewhere there the lpg tank brackets while arent in same spot are in the way and the triangle bit wont clear the brackets without undoing the brackets and lifting tank.

could you just undo the brackets and lift that end of the tank up so the triangle part in photo clears them then bolt it back up after or how do you get around the tank.

cars a ef fairmont sedan and hd tow bar which is what questions about is also a ef sedan tow bar

need some answers

car10002 is offline   Reply With Quote Multi-Quote with this Post
Old 23-08-2014, 07:04 PM   #2
xxx000
FF.Com.Au Hardcore
 
Join Date: Aug 2007
Posts: 1,874
Default Re: heavy duty tow bar

Confusing post

towbars are different for petrol & LPG Falcons. Got the right one ?
xxx000 is offline   Reply With Quote Multi-Quote with this Post
Old 23-08-2014, 08:06 PM   #3
car10002
FF.Com.Au Hardcore
 
Join Date: Aug 2010
Posts: 1,646
Default Re: heavy duty tow bar

All else is good both the car it came off and the one it's going onto are ef and sedans
car10002 is offline   Reply With Quote Multi-Quote with this Post
Old 23-08-2014, 08:07 PM   #4
car10002
FF.Com.Au Hardcore
 
Join Date: Aug 2010
Posts: 1,646
Default Re: heavy duty tow bar

The gas tank needs to be lifted a couple mm or a bracket made to work around the tank
car10002 is offline   Reply With Quote Multi-Quote with this Post
Old 24-08-2014, 06:55 PM   #5
Davehoos
FF.Com.Au Hardcore
 
Join Date: Sep 2013
Location: Karuah Valley
Posts: 984
Default Re: heavy duty tow bar

are you talking about a gas tank with brackets. with a tank cradle it would be easy.

front bracket would be ok but ive come across 2 different rear brackets.

one I fitted to EB Manchester that the bolts go in horizontal and might be a worry. the other AU tank went vertical through your bracket.so you may only need to drill and add spacer.

spacer at the front would be made from 50mm square or a flat bar between both the 2 lugs. but you need clearance on the parcel shelf.
__________________
BF11 XT EGas Wagon-SY TERRITORY AWD GHIA-
Land Rover 88
.MIDCOAST NSW.
Davehoos is offline   Reply With Quote Multi-Quote with this Post
Old 24-08-2014, 10:13 PM   #6
car10002
FF.Com.Au Hardcore
 
Join Date: Aug 2010
Posts: 1,646
Default Re: heavy duty tow bar

talking about a tank with brackets would the tank have to come out or can it just be slid or lifted a couple inches to get the triangle bit in that goes in the boot

would it matter if you didnt use the triangle bit that goes in the boot to bolt the bit infront of diff that bolts to that part through the floor or can you just cut up thick flat bar to go on the bolt holes in the floor that that triangle part would normally go in in the boot.

or can you modify the triangle part like cut the flat bar on it shorter so that bit goes between the lpg tank brackets and weld more flat bar and weld those ends back so it goes around the brackets on the tank

is there a way to modify the triangle part in boot so it clears the gas tank
car10002 is offline   Reply With Quote Multi-Quote with this Post
Reply

Thread Tools
Display Modes

Forum Jump


All times are GMT +11. The time now is 05:58 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL