![]() |
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
The Pub For General Automotive Related Talk |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 | ||
Starter Motor
Join Date: Feb 2018
Posts: 7
|
hey can any one help me. ive got a ba 6 in a jet boat running standard car computer which i got from a guy in ausie that he has flashed it and taken out security stuff. Ive had it running in the boat and runs great but i get to a point where the computer goes into limp mode. so have rung guy in ausie and he has said that i need to put a speed sensor onto the vss terminal on eec-b07.
so my question do i take power for sensor from battery or do i need to to get the supply from some where else on the computer. hope some one can help. cheers steve |
||
![]() |
![]() ![]() |
![]() |
#2 | ||
FF.Com.Au Hardcore
Join Date: Jun 2011
Location: Pt Lincoln far side South Oz
Posts: 5,780
|
your in New Zealand?
Is yours a Hamilton Jet boat? ![]()
__________________
Dont p i s s off older people. At our age the term Life in Prison is not a deterrent |
||
![]() |
![]() ![]() |
![]() |
#3 | ||
FF.Com.Au Hardcore
Join Date: Apr 2005
Location: Geelong, VIC
Posts: 5,265
|
According to the workshop manual the vehicle speed can be taken from the output shaft speed sensor in the transmission housing.
PCM pin B7 - Vehicle speed signal VSS PCM pin B45 - Vehicle Reference Voltage (VREF) PCM pin B33 - Signal Return (SIGRTN) Good luck. |
||
![]() |
![]() ![]() |
![]() |
#4 | ||
Starter Motor
Join Date: Feb 2018
Posts: 7
|
great ill give that a go. yes im in nz and yes its a hamilton jet boat. its an older jet 44..
|
||
![]() |
![]() ![]() |
![]() |
#5 | ||
FF.Com.Au Hardcore
Join Date: Feb 2008
Location: WA
Posts: 3,705
|
Id love to see a barra T in a boat. Straight pipe ftw.
It would shame many a 350.
__________________
www.bseries.com.au/mercurybullet 2016 Falcon XR8. Powered by the legend that is - David Winter. XC Cobra #181. 1985 Mack Superliner, CAT 3408, 24 speed Allison. |
||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#6 | ||
Starter Motor
Join Date: Feb 2018
Posts: 7
|
yes mercury bullet my brother and i have discussed that and are quite keen
|
||
![]() |
![]() ![]() |
![]() |
#7 | |||
FF.Com.Au Hardcore
Join Date: Apr 2005
Location: Geelong, VIC
Posts: 5,265
|
Quote:
BPRacing are working on a barra turbo boat project BPRacing has successfully sparked life into the jet boat project Today BPRacing have some fun on the water at Barwon Heads tuning the 4.0L Barra turbo in steves boat. Pretty awesome! |
|||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#8 | ||
Starter Motor
Join Date: Feb 2018
Posts: 7
|
ok so ive had a look at the b connector on the ecu. still a bit confused. another thread ive read under ecu on this forum said b7 is the signal in. im confused on which supply do i take to power up the proximity switch.
sorry if im slow on the pick up. cheers for any help |
||
![]() |
![]() ![]() |
![]() |
#9 | ||
FF.Com.Au Hardcore
Join Date: Apr 2005
Location: Geelong, VIC
Posts: 5,265
|
Your sensor will have 3 wires, 1 wire is for the speed signal from the sensor into the pcm.
The second wire will be power, the third will be return/ground wire. So from above B7 is signal from the sensor into the pcm B45 is the power supply from the pcm to the sensor (could be 5V or 12V not sure use multimeter to test) B33 is the signal return/ground from sensor to pcm. Good luck. |
||
![]() |
![]() ![]() |
![]() |
#10 | ||
Starter Motor
Join Date: Feb 2018
Posts: 7
|
thanks mate that makes sense
|
||
![]() |
![]() ![]() |
![]() |
#11 | ||
Starter Motor
Join Date: Feb 2018
Posts: 7
|
ok ive got it to work. I used a 12v proximity sensor hook it to + and - battery and used the signal back into b7 and it comes up with a speed so going to test it on the water.
|
||
![]() |
![]() ![]() |
![]() |
#12 | ||
Moderator
![]() ![]() Join Date: Feb 2005
Location: Kenthurst
Posts: 40,394
|
Eagerly awaiting video
![]()
__________________
The Current Stable 2016 SZII TS Territory RWD Petrol The Evolution of the EGA54D utes AU Workshop Build thread of EGA54D B-Series Workshop Build thread of EGA54D 2004 SX TX Territory AWD - Gone but not forgotten 2010 FG XT "The ex-rental" - Moved onto a new home Mechan1k's Flickr Page |
||
![]() |
![]() ![]() |
This user likes this post: |