mr. fez finally lowered

zetec jim · 23-06-2009, 02:26 PM

Just an update... more pics and measurements etc... to come but just drove the fez home from getting lowered on Kings Springs.

first impressions (20min drive)....GREAT! takes corners a lot better, and looks meaner...especially from the back :evil3:

I reckon the Kings i think aren't that bumpy or crashy at all, and thats driving home on all the crappy tram tracks etc... still to take it up to the Dandenongs for a run (also to visit the old man whos just bought a Pirelli GTI

: )

will post up more specifics (ride drop and photos) later after it has a wash

Argh-Ess · 23-06-2009, 09:55 PM

I got my WQ on king springs at the moment, not too bumpy but still a bit of body roll though. Have you still got the standard shocks? Im keen to upgrade but dunno what to go for.

Twinpiston · 23-06-2009, 10:39 PM

Wow what a coincidence, just done mine, how much has yours dropped by?

I think I dropped about 35mm rear and 40 oddmm front, looks hot on the stockie 15" pursuit rims!!!!

On the rear, are the progressive sections at the bottom or the top on yours?

Cheers

Vision Zetec · 24-06-2009, 09:21 AM

Pics!!!

bru20vt · 24-06-2009, 10:22 AM

Quote:

Originally Posted by Twinpiston

Wow what a coincidence, just done mine, how much has yours dropped by?

I think I dropped about 35mm rear and 40 oddmm front, looks hot on the stockie 15" pursuit rims!!!!

On the rear, are the progressive sections at the bottom or the top on yours?

Cheers

Assuming you are using Eibach springs.

Interested in this also - I have been told that if they are installed correctly the bottom 4 coils are completely compressed. The other signs are that the plastic sleeve should be on the bottom coils and that the writing on the springs should be legible ie not upside down. Is this how yours are?.

If you can, I wouldnt mind knowing what numbers are on the rear coils.

dom

Twinpiston · 24-06-2009, 02:37 PM

I got Kings as well.

The writing is correct way up, but my springs are compressed on the bottom, which looks cool and according to Kings themselves, is ok to have this way.

Their is no sleeve on the spring in the rear (not sure about the front I didn't do them), just the rubber mount on top and plate on the bottom...

Pics to come soon.

Fled74 · 26-06-2009, 04:13 PM

Pics please!

I almost had some King springs fitted as well (I had some extra cash), but had second thoughts. The roads I regularly drive on can be a bit on the rough side so firmer springs would have made the ride too uncomfortable.

Twinpiston · 26-06-2009, 09:21 PM

Here they, terrible quality, bloody Blackberry.

I will try and get some more when the rain stops and I can clean the 2 cars.

17" MP3s are going on after I get back from O/S....

I will also finish colour coding the car. (washer jets, mirror caps and boot strip currently done.)

Argh-Ess · 26-06-2009, 11:17 PM

haha, looks cool on the steelies. Here is mine - King Springs with XR4 rims...

robjh80 · 27-06-2009, 09:52 AM

Quote:

Originally Posted by bru20vt

Interested in this also - I have been told that if they are installed correctly the bottom 4 coils are completely compressed.

Correct .. whether you have Kings, Eibach's, Spax .. whatever, the progressive springs should be compressed at the bottom to make them work properly.

The plastic sleeving is to help stop the springs "clanking" together and making you wonder what the hell is wrong with your car ..

If you have the progressive springs compressed at the top rather than the bottom they are not installed correctly ... "Ya Doing It Wrong!"

zetec jim · 27-06-2009, 08:24 PM

Righto... some pics (be they of an unwashed fez) now its lowered.

previous ride height
(middle of centre cap to wheel arch exterior):

Front - 350mm
Back - 355mm

Current Ride Height

Front - 310mm
Back - 320mm

I think my springs have the compresses section at the top

: !
Is this worth changing, or will they work alright as is? I think i'm hearing that clank as well... although they same work fine.

kiwijohn42 · 27-06-2009, 10:39 PM

Nice, there's only one thing missing...

Twinpiston · 28-06-2009, 08:52 AM

????????????

kiwijohn42 · 28-06-2009, 09:32 AM

The side skirts for the body kit are still in his garage

Twinpiston · 28-06-2009, 09:35 AM

Aaahhhhhh,

If only I could find some cheap enough, and may be only in Panther Black.

robjh80 · 28-06-2009, 10:15 AM

Quote:

Originally Posted by zetec jim

I think my springs have the compresses section at the top

: !
Is this worth changing, or will they work alright as is? I think i'm hearing that clank as well... although they same work fine.

I would mate, it's not a difficult job to take the rear springs out on the Fez

Just jack it up at the back, put in a couple of axle stands to support the car and the rear springs can be compressed by hand and lifted out.

Twinpiston · 28-06-2009, 10:47 AM

I'll second that, I did the rear springs myself.

Getting the originals out was slightly harder, with out spring compressors.

But if I had to turn them around again it wouldn't be that hard, maybe 30 minutes...

Hopefully getting clean shots up this afternoon.

zetec jim · 28-06-2009, 03:44 PM

thanks guys, its due for a service soon, so i'll get my mechanic to do it.

haha Kiwijohn.... You know too much.....

Might get them done soon. I would spray them and put them on myself, but they are an aftermarket skirt, and are for a 5 door model, so need some cutting to make them fit. one day...... thinking bout a strut-brace and rear-sway-bar first though... :eclipsee_

Twinpiston · 28-06-2009, 08:54 PM

Ok, I have deleted the other files cause they were just wrong..

Here goes

And my special S

Ben85 · 29-06-2009, 04:30 PM

Quote:

Originally Posted by Twinpiston

On the rear, are the progressive sections at the bottom or the top on yours?

Cheers

Well heres the answer guys. I emailed king springs and the progressive (bunched up) coils on the rear of the car should be at the top, not the bottom. Hope that helps

zetec jim · 29-06-2009, 05:38 PM

thanks for that ben, one less thing to worry bout

dannyhilton · 29-06-2009, 06:36 PM

Looks hot Zetec Jim. You've certinly got a tidy peice there! My Diamond White Zetec looks almost bland when compared to your model. The colour coding does no end of good for the look of the car. The back, with the color coding, dual pipes and body kit looks absolutly horn. The only advantage mine has over your one is it has the side skirt, which I think would top your model off nicley. Would it fit with the lowering though, or would it scrape too much?

chinw3e · 29-06-2009, 07:24 PM

Haha twinpiston, my fiesta is pretty much a replica of yours. just a bit dirtier, and my astra wiper broke. :( but I agree, they look stealthy lowered on the stickies ;)

Twinpiston · 29-06-2009, 08:42 PM

Yep got the MP3's waiting to go on, got a bargain with the tyres, so soon.

I too rang kings and talked with their engineer and he said the only reason they put them on the top is to stop dirt and gunk getting stuck in the progressive section.

I said mine were installed with this section at the bottom and said thats fine....

Personal choice I suppose

robjh80 · 29-06-2009, 09:39 PM

Quote:

Originally Posted by Ben85

Well heres the answer guys. I emailed king springs and the progressive (bunched up) coils on the rear of the car should be at the top, not the bottom. Hope that helps

Obviously your email was opened by the snotty nosed 17 year old sales cadet who at the time was helping the girls out with a bit of filing in the office and thought he'd help himself to a little bit of a tamper with the computer.

Ben85 · 29-06-2009, 11:03 PM

As im not a mechanic i just emailed the company that i bought the springs from, they have informed me that this is the correct way to fit these springs. I have no idea where your getting your information from. So im inclined to believe King Springs.

Twinpiston · 29-06-2009, 11:55 PM

I guess it comes down to who you spoke to.

I got a different answer...thats all

zetec jim · 30-06-2009, 04:05 AM

Quote:

Originally Posted by RapidTyphoon

Looks hot Zetec Jim. You've certinly got a tidy peice there! My Diamond White Zetec looks almost bland when compared to your model. The colour coding does no end of good for the look of the car. The back, with the color coding, dual pipes and body kit looks absolutly horn. The only advantage mine has over your one is it has the side skirt, which I think would top your model off nicley. Would it fit with the lowering though, or would it scrape too much?

thanks man, yeah, still iffy about putting the side skirts on, i think to get em' painted and fitted would be money well spent on other things (strut-brace, rear sway-bar, better tyres when it comes round....maybe even some 17"s,... plus i'm thinking bout changing the front seats to something more hugging... IE Sparco/Recaro/OMP/Bride... I really want some mid-corner bolstering (Iwant the Sparco's) :evil3: )

:

Twinpiston · 30-06-2009, 07:06 AM

Which ones and where from?

I find my seat a little uncomfotable in the lower half!!

zetec jim · 30-06-2009, 11:32 AM

dunno yet, just looking on ebay till the right ones come up...dont want to spend a fortune, because i'll probably end up having to buy a spare set of fiesta seats so i dont screw up my stock rails.