EB central locking button

[ebfalcon13.5]

hey i was wondering what would i have to do to wire a button to the central locking system on my EB to unlock the doors similar to the EF falcon? thanks

[holmsy]

shouldent be to hard my ed has a button.
try find out how the ed is wired up and either change over some ed parts or work out how to adapt it.

[ebfalcon13.5]

ok sweet an ed button will look neater then my a/m switch i was gonna chuck in does anyone know where the wires end up? do they have to be ran inside the door trims to the actuators?

[Zedjay]

my EB has one too (standard)

what year model is youre EB??

[holmsy]

i dont know what the switch connects to. but if it connects into the ecu or a computer you can probably just wire it up the same and it will work. try go to a wrecker and see where the wires go.

[ebfalcon13.5]

Originally Posted by Zedjay

my EB has one too (standard)

what year model is youre EB??

its a '91 model

[ebfalcon13.5]

Originally Posted by holmsy

i dont know what the switch connects to. but if it connects into the ecu or a computer you can probably just wire it up the same and it will work. try go to a wrecker and see where the wires go.

ok i will do that heading over there for a bit on sunday probably im trying to look for a pinout diagram for my ecu but i can only find eb series II diagrams.. is the ecu in my series I the same as this

[EA2BA]

They ECU pin out basically fall into the below catagories, and then smartlock and non smartlock for most of the below.

EA 3 speed auto/manual
EA-EB with seperate trans controller
EB-ED 4 speed intergrated auto/manual
EF - auto/manual
EL - auto/manual (very very close to the EB-ED 4 speed intergrated auto/manual)

[EA2BA]

Smartlock controls the doors on cars with a button, to use the button in any other car you will need to wire up some relays etc to send the correct signal down the actual door lock wires to lock/unlock the car (much the same as adding an aftermarket alarm)

[ebfalcon13.5]

Originally Posted by EA2BA

They ECU pin out basically fall into the below catagories, and then smartlock and non smartlock for most of the below.

EA 3 speed auto/manual
EA-EB with seperate trans controller
EB-ED 4 speed intergrated auto/manual
EF - auto/manual
EL - auto/manual (very very close to the EB-ED 4 speed intergrated auto/manual)

ok thanks that helps a bit its non-smartlock and either one of these:
EA-EB with seperate trans controller
EB-ED 4 speed intergrated auto/manual
how can i tell?

[EA2BA]

is it auto or manaul ?

[ebfalcon13.5]

ive found this link http://fordmods.com/forums/documents.php?doc=41 i think it falls into the "EB-ED 4 speed intergrated auto/manual" but my cars a series one not two

[ebfalcon13.5]

Originally Posted by EA2BA

is it auto or manaul ?

4 speed auto

[EA2BA]

ok under the dash (steering wheel) on the left side (nearest the middle of the car) you should see a metal box with big yellow plugs going into it, if you do then its non intergrated and thats the trans controller.

I am willing to bet this what you have, so that means you basically need an EA 3 speed auto ecu wiring diagram.

Do you have 2 TPS's on the throttle body?

[ebfalcon13.5]

Originally Posted by EA2BA

Smartlock controls the doors on cars with a button, to use the button in any other car you will need to wire up some relays etc to send the correct signal down the actual door lock wires to lock/unlock the car (much the same as adding an aftermarket alarm)

that clears things up

[EA2BA]

Use this if I am correct:
EA Series 1 - ECU
PIN wire colour Description
1 yellow Keep Alive Memory Power
2
3 white Vehicle Speed Sensor
4
5 red/green Key Power - B+ when igntion is switched on
6 yellow Power Steering Pressure Switch
7 greeen/yellow Engine Coolant Temperature sensor
8
9
10 blue Air Con Clutch Relay
11
12
13
14
15
16 black Ingition Ground
17 white/black Self test output
18
19
20
21 grey/white Idle Speed Control Device
22 brown/green Fuel Pump Relay or circuit
23
24
25 yellow/red Air Charge Temp
26 orange/black Sensor Volatge Ref +5v
27
28
29 green/blue Heated Exhaust Gas Oxygen sensor
30 orange/black Neutral Drive switch
31 yellow/blue Canister Purge enable output
32
33
34 green/yellow Serial Data Output Port (Link) TRIP Comp
35
36 yellow/green Spark Output from the EEC IV
37 red Vehicle power B+
38
39
40 black/green Vehicle ground battery negative (-)
41
42
43
44
45 blue/yellow Manifold Absolute Pressure
46 black/white Zero ref for most sensors
47 green/black Throttle Position Sensor Voltage
48 white/red Self Test Input
49 grey/blue Heated Exhaust Gas Oxygen sensor GND
50
51
52
53
54
55
56 brown Profile Ignition Pulse
57 red Vehicle power B+
58 dark brown bank 1
59 green bank 2
60 black/green Vehicle ground battery negative (-)

[ebfalcon13.5]

Originally Posted by EA2BA

ok under the dash (steering wheel) on the left side (nearest the middle of the car) you should see a metal box with big yellow plugs going into it, if you do then its non intergrated and thats the trans controller.

I am willing to bet this what you have, so that means you basically need an EA 3 speed auto ecu wiring diagram.

yes i do have the metal box there with a yellow plug

Originally Posted by EA2BA

Do you have 2 TPS's on the throttle body?

not quite sure what your talking about sorry

[EA2BA]

Then use what I posted above, the wire colours may not be 100% correct on your car (they are taken from my car EA), but will be correct for pin assignment

[ebfalcon13.5]

Originally Posted by EA2BA

Then use what I posted above, the wire colours may not be 100% correct on your car (they are taken from my car EA), but will be correct for pin assignment

thanks a lot for that, which site did you get these from or is this your work?

[EA2BA]

It's my own work, so I know its correct cause I sat down and went through each wire and checked and cross referenced back to the gregories as to the function of the wire as well. I did that for adding the 4 speed auto to my car.

[EA2BA]

This is the 4 speed Trans controller as well:

4 Speed Auto Trans Computer (TCU)
PIN wire colour Description
1 Blue/Yellow Temp Sensor (input)
2 Orange Diagnostics (input)
3 NOT USED
4 Blue Air Con status (input)
5 Blue/Orange Temp Sensor ground
6 Pink Ignition system, engine speed signal (input)
7 Green Solinoid 5 return (input)
8 White/Red Diagnostics (ground)
9 Blue/White Throttle Position (ground)
10 Violet/White Shift Lever Position (ground)
11 Green/Yellow Solinoid 4 (input)
12 Green/Black Solinoid 1 (output)
13 Yellow/Red Solinoid 6 (output)
14 Green Mode indicator dash light (output) Negative (-)
15 Yellow/Black Battery Positive (power)
16 Blue/Red Throttle Position (input)
17 Violet Shift lever (input)
18 Red Econ/Preformance Mode switch (input) Negative (-)
19 White Shaft SApeed Sensor (input)
20 Green/Blue Diagnostics (output)
21 Black Ground
22 NOT USED
23 NOT USED
24 NOT USED
25 Blue/Green Throttle position sensor reference 5v (power)
26 Green/Red Solinoid 3 (input)
27 Green/White Solinoid 2 (input)
28 Yellow/Green Solinoid 7 (output)
29 Yellow Solinid 5 (output)
30 Red/Green Ignition switch (power)

[ebfalcon13.5]

thanks again for that EA2BA, you dont know how long ive been looking for that info!

[EA2BA]

Not a problem when it comes to ea wiring at least, i have pulled apart and mapped nearly every wire in my car, and added a lot more too

[ebfalcon13.5]

i now know who to ask if i have any trouble wiring in my eb! ;)

[EA2BA]

anytime, good luck with project