Welcome to the Australian Ford Forums forum.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact us.

Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated.

Go Back   Australian Ford Forums > Club and Speciality Forums > Forum Community Car Clubs > OzECruisers (E/N/D Series) > OzECruisers General Discussions

OzECruisers General Discussions E/N/D vehicles General Discussion ONLY. NO TECH THREADS

Reply
 
Thread Tools Display Modes
Old 21-02-2007, 02:12 PM   #1
El Venom
normality is boring
Donating Member1
 
El Venom's Avatar
 
Join Date: Jun 2006
Location: Up in the hills on the QLD/NSW boarder
Posts: 1,803
Default lowest your car can legally be in qld

does anyone know the height your car can be at the lowest point and still be legal in queensland?

El Venom is offline   Reply With Quote Multi-Quote with this Post
Old 21-02-2007, 02:29 PM   #2
EA2BA
PM me if you want
 
EA2BA's Avatar
 
Join Date: Dec 2004
Location: Pk Ranger Modding - QLD 👍
Posts: 7,498
Default

Any car in any state it's a lowest point of 100mm best I know of.
__________________
Owner of first ever car to retrofit BA SSS - the EA2BA

Send me a PM if you want to know anything

2010 Ford Ranger PK High Rider (Auto) - 2011 Ford Fiesta (Auto)
EA2BA is offline   Reply With Quote Multi-Quote with this Post
Old 21-02-2007, 03:32 PM   #3
nicko_bud
Regular Member
 
nicko_bud's Avatar
 
Join Date: May 2006
Location: Adelaide
Posts: 157
Default

The road clearance of a fully laden vehicle must not be less than 100mm Measured at any part of the vehicle other than the wheel rim or brake backing plates. (This does not apply where a lesser clearance has been
specified by the manufacturer.)

When lowering or raising a vehicle body (front or rear), the following additional restrictions are based on the manufacturer's dimensions for the standard unmodified vehicle while unladen:

• The ride height measured between the rubber bump stop and the corresponding metal stop may be reduced by no more than one third.

• The rebound travel measured between the rubber rebound stop and the corresponding metal stop (or the extension of the shock absorber for vehicles
without a rebound stop) may be reduced by no more than one third.

• Coil springs are to remain in locating seats on full suspension droop without forcibly being removed. In addition, the normal relationship between the front
and rear suspension heights must not be unduly affected. Replacement springs (shorter or taller) must have the same or greater load capacity as the original springs.

Suspension coil springs must not be shortened by cutting or heating. Leaf spring suspensions must not be raised by the use of extended shackles, adjustable metal plates or by placing the leaf springs to the opposite side of the axle. If lowering blocks are used, they must be either steel or aluminium.

Airbag or air pressurised shock absorber helper springs may be fitted in addition to the original suspension. However, replacing some or all of the suspension system with an air or hydraulic suspension requires specific approval
nicko_bud is offline   Reply With Quote Multi-Quote with this Post
Old 21-02-2007, 04:42 PM   #4
El Venom
normality is boring
Donating Member1
 
El Venom's Avatar
 
Join Date: Jun 2006
Location: Up in the hills on the QLD/NSW boarder
Posts: 1,803
Default

i hae heard somewhere that it has recently changed due to some of the new cars being released are actually lower then 100mm from the factory.I was also told the new messurement is 80 - 85mm, but i have been unable to confirm this. has anyone else heard this. Also would the height be a roadworthy item as my car is between 80 and 85mm off the ground at the lowest point of the exhaust
El Venom is offline   Reply With Quote Multi-Quote with this Post
Old 21-02-2007, 05:08 PM   #5
nicko_bud
Regular Member
 
nicko_bud's Avatar
 
Join Date: May 2006
Location: Adelaide
Posts: 157
Default

Read BOY!!!! ive highlighted in BOLD

The road clearance of a fully laden vehicle must not be less than 100mm Measured at any part of the vehicle other than the wheel rim or brake backing plates. (This does not apply where a lesser clearance has been
specified by the manufacturer.)
nicko_bud is offline   Reply With Quote Multi-Quote with this Post
Old 21-02-2007, 07:14 PM   #6
El Venom
normality is boring
Donating Member1
 
El Venom's Avatar
 
Join Date: Jun 2006
Location: Up in the hills on the QLD/NSW boarder
Posts: 1,803
Default

so is the height a road worthy item
El Venom is offline   Reply With Quote Multi-Quote with this Post
Old 21-02-2007, 07:21 PM   #7
jabba
FF.Com.Au Hardcore
 
jabba's Avatar
 
Join Date: Jan 2005
Location: Is that your face, or did you neck throw up
Posts: 3,041
Default

Quote:
Originally Posted by daendo
so is the height a road worthy item
Yes it is.. Nicko Bud explains it all.. If a cars suspension does not fit into that criteria than it is not roadworthy
__________________
Built by HERROD MOTORSPORT

Tuned by Elite Automotive

11.91 @ 117mph Vid
jabba is offline   Reply With Quote Multi-Quote with this Post
Reply


Forum Jump


All times are GMT +11. The time now is 04:54 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL